PVC Beadboard Kit, 36" H, 8 ft

Score: 4.33 (votes: 6)
(1)
1

Interior PVC Beadboard Kit 8 feet long in pre-finished white  vinyl 36" high to cover 8 running feet of wall*. No painting required but can be painted. This kit contains all the trims needed. Eight Planks (8 ft long) may have to be cut down to 3 sections of about 32" on site. The cap and baseboard add 4" the the height of the planks.

*Actual length is 95”, which is the maximum length allowed for parcel shipping.

  • US$146.72
Quantity:  
OR
  • NOTICE

    Please see our Covid News for the most current news relating to availability, closures, and lead times.

  • Vinyl Wainscoting How To

    Detailed installation instructions

  • SKU
    PVC-BB-36-W
  • Weight
    8 lbs

Interior PVC Beadboard Kit 8 feet long in pre-finished low maintenance vinyl white  36" high to cover 8 running feet of wall. No painting is required but can be painted. This kit contains all the trims needed. Eight PVC Planks 8 ft. long*, to be cut down to 3 sections of about 32" on site. The PVC planks are ¼” thick and 4 ¼” wide, of which approximately 4” is exposed. The beads are 2” on the center. The cap and baseboard add 4" to the height of the planks. The wainscoting cap is 1-5/8" x 95   " and made of ¾” thick material. The base moulding is 3-1/2" x 95" and is made of 5/8” thick material.

*Actual length is 95”, which is the maximum length allowed for parcel shipping.

We are Open 

Online ordering, manufacturing & shipping.  

Showroom & pick-up's by Appointment.

Latest Covid News

We are currently experiencing a high demand of orders and longer than expected lead times from our vendors.  Our team is working hard to process all orders, as soon as possible; however, we must maintain safe working standards, along with social distancing measures, to ensure their and your safety are our highest priority.  

Anticipate delays and longer than normal lead times.  Thank you for your understanding during this challenging time.  

Note our Showroom is open, by appointment, we are open Mon-Fri 9 - 5 and Saturdays 10 - 3 EST for scheduled showroom appointments and scheduled pick ups.  

We are always available for online ordering, and continue shipping orders and manufacturing.  Our team members are here ready to assist you with your project needs.

We look forward to hearing from you!

Elite Team.

INSTALLATION INSTRUCTIONS FOR VINYL WAINSCOTING

“Perfect Finish” Ready-to-Install PVC/Cellular Composite Wainscot * NO PAINTING REQUIRED!

Its made from high strength PVC materials. This material works like wood: cuts, glues or nails. However it will not splinter or crack and has no knots. This product has a lifetime warranty on rot. The product is for interior use only.

Tools:  Mitre Saw or Hand Saw, Hammer, Level, Square, Caulking Gun, Tape Measure, Pencil

[image 1 ]
Additional Materials
Panel Adhesive (PL Premium or No More Nails Tub Surround), 1’’ finishing nails or brad nails (Optional)Installation Tips

Use a quality panel adhesive and follow manufacture’s instructions. When tapping panels into each otheruse a wood block or end cut of one of the panels. Do NOT use the hammer directly on the panel or butt panels too tighly. Allow for normal expansion and contraction (1/32").

For better holding strength angle all nails and drive nails leaving 1/8” above surface and finish using a nailset. When possible nail into moulding groove. This avoids surface damages. For cleaner cut, saw into the finished surface.

When you approach an outlet, turn off the power. Take careful measurements of the outlet location and cut out the opening.

Installation: Base Trim

Measure your wall, if your wall is longer than 8’ pre-mitre the joining end with the next piece of base board you will be using.
[image 7 ]

Make certain the Base Trim has the pre-grooved end up before glueing or nailing. Apply glue in a zig-zag pattern on back of Base Trim and apply to wall. Make sure Base Trim pieces align on the wall
[image 2 & 3 ]

Installation: Panel

The correct installation of the first panel board is the key to an easy and successful installation.

Begin at the left most corner of your installation (opposite if you are left-handed). Each panel is tongue and grooved for a uniform fit and easy installation. Determine which side you want to enhance your room beaded or smooth. Keep the groove edge towards the starting corner. Using a level make sure the first panel is absolutly square. When necessary, scribe and remove material from the panel from the groove

side (inside corner).

[image 4 ]

Next, determine the height you want for your wainscot and cut only if necessary.

[image 5 ]

Do not force fit pieces together. Apply glue on back side of panel place into groove on Base Trim and position into corner.
[image 6 ]

(Optional) Nailing the top, middle and bottom tongue every 16” will ensure better adhesion.Carefully measure and fit next panels. The last panel may also need to be trimmed to fit into the corner.

Installation: Chair Rail

Make sure that all panels are correctly installed.Measure your wall, if your wall is longer than 8’ pre-mitre the joining end with the next piece of Chair Rail you will be using.
[image 7 ] Make certain the Chair Rail has the pre-grooved end down before glueing or nailing.

Apply glue in a zig-zag pattern on back of Chair Rail and apply to wall. Make sure Chair Rail pieces align on the wall.
[image 2 & 3 ]

Maintenance

Cleaning your Vinyl Millwork with a damp cloth makes it look like new.

Customer reviews
Average rating:
4.33 (Votes: 6)
Rating of votes (6)
5
 
 
4customers
4
 
 
1customers
3
 
 
0customers
2
 
 
1customers
1
 
 
0customers
 
Please sign in to add review
  • James Medalie
    Dec 28, 2019, 10:56 AM
    The kit came quickly and was easy to install. Looks very nice on the wall. I would be happy to send pics. I recommend this kit as the surface finish is very nice and does not need to be painted.

Related products