We will be closed on Monday October, 9th 2023 for Thanksgiving / Columbus Day.

8" Recessed Fibreglass Column

Score: 4.78 (votes: 9)
8" Recessed Paneled, Square, Lightweight Pultruded Fiberglass Column, complete with Box Base and Capital, as well as top and bottom dividers as shown. Please note, middle dividers are available at an additional cost. We ship each Column with all the necessary Tapcon Screws and mounting hardware. They are manufactured from the most advanced fiberglass in the construction market which makes them last a lifetime.  
  • US$179.53
  • Column Installation Tips & FAQs

    Find helpful tips, specifications and installation advice on how to install our Columns. Read through the instructions to see if this is the right product for you.

  • SKU
8" Recessed Paneled, Square, Lightweight Pultruded Fiberglass Column, complete with Box Base and Capital, as well as top and bottom dividers as shown. Please note, middle dividers are available at an additional cost. We ship each Column with all the necessary Tapcon Screws and mounting hardware.

Pultruded Columns are made by a Pultrusion process and have the look of cast fibreglass columns at a lower cost! The process involves pulling continuous lengths of reinforced polymer, rather than pushing, as in extrusion through a forming die using a continuous pulling device. Resin, fillers and specialized additives are then added to produce a fine finish.

Though Pultruded Columns look the same as HB&G Permacast Columns, they carry only about half of the load-bearing capacity or about 8,000 Lbs, which will due for most applications. They are lighter in weight than the equivalent cast columns which makes them easier to ship, carry and install. Another difference between the columns is that the Pultruded columns cannot be split. These Pultruded columns are resistant to chemicals, rot, fading, insects, warping and moisture. Pultruded Fiberglass Columns come with a limited lifetime warranty for material and workmanship when properly installed.

This column comes with loose panel dividers for the top and bottom of the shaft to be glued in place. This allows for the customization of panel sizing. Middle dividers can be added to the column for a look of more panels if desired. Middle dividers must be ordered separately.   The dividers, capital and base are to be glued in place with construction adhesive which is not included.


Shaft only

with Box Cap / Base

with Tuscan Cap / Base

with Tuscan Cap / Cap

Top Footprint

7 1/4"

8 ¾”

10 ⅜”

10 ⅜”

Bottom Footprint

7 1/4"

8 ¾”

11 ⅛"

10 ⅜”

Cap Height


3 ⅝”



Base Height


7 ¼"

4 ½"


Permalite Installation Instructions              Specifications & Load Bearing Data

The astragal or neck moulding can be ordered separately if desired.

    • SKU
  • Production Time
    Quick Ship
  • Tarrif Code
  • Shipping Cost
    Call for transport quote.
    Limitations to our Shipping Specials
  • Capital & Base Set
    Box, Tuscan
  • Extra Divider for Center Panel
    No, Yes
  • Height
    12 ft., 10 ft., 8 ft., 6 ft., 4 ft.
Non-Tapered PVC Wrap
Installation Tips
Tapered PVC Wrap
Installation Tips
Craftsman PVC Wrap
Installation Tips
Large PVC Columns
Installtions Tips
Installing Exterior Columns
Video   PDF
Installing Square
Permacast Columns
Fiberglass Columns
Installing PVC
Panel Kits

Re-Assembling PVC
Column Shaft

Adding PVC
Column Extention
How to Install HB&G
Porch Posts
Fiberglass Column
Load Bearing Data
All PVC Capital and
Base Specifications

Installing Dividers
on Columns

Installing Box Caps/Bases
on Fiberglass Columns
Painting Tips for
Columns & Cellular PVC
Installing Georgian Bases
on Tapered Columns

 Custom Tapered
Column Form

PVC Trim Warranty

PVC Trim | Sheets
Installation Guide
Help on Choosing
Wood Columns
Wood Columns
Load Bearing Chart
Installing Wood Columns
Installing Round
Stain Grade Columns
Assembling Square Paneled Columns
Covering Posts in Basements
Square Shaft Assembly
Joining Split Wood Columns
Joining Split Fiberglass Columns
Standard Flute Lengths for Columns
Custom Fluted
Column Form

Installing a Split
Column as a Pilaster
Glossary of Terms


Are you the manufacturer?
Elite Trimworks does produce most of our interior columns and most exterior columns.  We specialize in manufacturing PVC Columns.

Are your columns load bearing?
Yes, all of our round wood and Fiber Cast columns are load bearing. Refer to website for the load bearing capability of the desired column.

If my wood columns are split, what type of adhesive do I need to reassemble them?
To reassemble a split column, a high quality wood glue adhesive should be used. This product can be found at any hardware or construction-supply provider.

How do I secure a split column to a wooden or metal post?
Depending on your application, there are several ways to hold a column in place when used for decoration purposes only. One of the most common ways to hold a column in place is to use standard "L" brackets on the bottom and top of the column's shaft. The Tuscan Base and Capital hide this method of installation. If being assembled around a wooden post, a common way to secure the column is by using wood shims. The shims should fit snugly between the column shaft and the post for proper stability. Be sure to visit our website for further column installation instructions.

Can I trim my columns to a lower height?
Yes. If it is a non-tapered column, 1/3 of the shaft height can be trimmed without affecting the fit of the base and capital. Trimming must take place from the bottom of the shaft only!

How are the columns shipped?
Columns measuring up to 8 feet are shipped using UPS. Any column longer than 8 feet must be shipped using a common carrier (Tractor Trailer) and different shipping rates apply.

What happens if my columns arrive damaged?
Depending on shipping method, different rules apply. For instance we do not allow UPS shipments to be refused. For transport shipments, it needs to be indicated on the Bill of Lading (BOL) and we need to be contacted right away. For complete details please see our Terms & Conditions

Is Elite Trimworks competitive with their pricing?
You bet ya! Our 20,000 square foot warehouse allows us to buy in volumes. Half of the columns we sell are made in-house and we pass on the savings to you. We are confident that our prices are some of the best out there. Give us a call and find out for your self.

 Can I install the columns myself or will I need a contractor?
Columns less than 9 feet are easy to manage for proper installation if you are handy with basic tools required. Our website has downloadable instructions for installation. Columns over 9 feet high are best managed with the assistance of an experienced contractor.

Can columns go around poles and beams?
Any column is capable of being split in order to accommodate your design. The rules are as follows: Round Beams take overall diameter; Square Beams, take diagonal measurement from top to determine width. Refer to our specs for inside clearance of the shaft to determine proper size column needed.

Do capital and base add any height to the column?
When you order a round wood column the capital and base are factored into the overall finished height of the column. When ordering the Fiber Cast columns, the capital and base are pieces that fit around the column (see image below) and so they do not play a part in adding height to the finished column.

Are the capitals load bearing?
Decorative capitals are strictly for decorative purposes and are not load bearing. The wood or MDF capitals that come standard with the wooden columns are load bearing.

Are your exterior columns insect and decay resistant?
All our exterior columns are engineered and tested to warrant against damage caused by exterior elements.

How are the columns approved for load?
All of our columns come with full strength and material testing provided from our local material testing facility and engineer, see individual products for exact load bearing data.

How wide should the column shaft be?
The width of columns are calculated in terms of a ratio between the base diameter of the shaft and the height. If you where looking for architecturally accuracy, a Tuscan or Doric column should be seven diameters high, an Ionic column, eight diameters high and a Corinthian column nine diameters high. For more on the “Orders of Architecture” go to www.en.wikipedia.org/wiki/Classical_order#Tuscan_order

 How should I paint my interior columns?
Bulls Eye 1-2-3®i (see site for complete details) a whole house, universal interior/exterior, water-base stain-killing primer-sealer. Excellent adhesion to glossy surfaces, including tile and enamelled trim. Low odour and easy-to-apply with great flow and levelling. Breathable, flexible acrylic formula resists blistering and peeling. This primer generally dries and is ready to expect paint within the hour.

Why should I discuss my project with you?
Speaking with us will ensure that you are getting the correct column for the job, our years of experience may prevent you from making costly errors.

Customer reviews
Average rating:
4.78 (Votes: 9)
Rating of votes (9)
Please sign in to add review
  • Joe Calarco
    Jul 10, 2019, 06:16 PM
    The fiberglass column looks amazing I install myself and the instructions that were provided were actuate
  • Dave Shannon
    Jun 12, 2019, 07:58 PM
    Excellent service, order arrived in a couple days, easy to cut and install. Highly recommend this product and company.

Related products