Cove Light Mouldings Packages Using 12V LED

Unlike the low intensity rope light used years ago, new and improved LED lighting is far more brighter. Todays Cove Lighting is much easier to install and far more efficient to operate. We use custom made stand off brackets that position the light strip perfectly for a smooth, even, and consistent glow across the entire ceiling. We offer every thing you need for Cove Lighting: many choices of cornice trim; stand off brackets; LED strip lights with 3M adhesive backing, and all the other accessories required.

A great looking ceiling project is dependent on keeping a consistent distance from the strip light to the ceiling. This ensures an even, balanced light across the entire room, including the corners. After years of experience, we have perfected this using the custom made MDF brackets listed on this page.If you have a project in mind, email us with a room layout and we can help you layout all the parts you need and work out a quotation for you.


>Basic Installation Instructions     >Power Supply Requirements

Per page:
Drop items here to shop
Product has been added to your cart
  • Drag and drop me to the cart

    With this connector, two rolls of LED strips can be easily connected to one power supply.

    • US$10.00

    Score: 5.00 (votes: 1)
  • Drag and drop me to the cart

    MDF Bracket for LED Strip Lighting in 8ft sections. A great looking ceiling project is dependent on keeping a consistent distance from the strip light to the ceiling. This ensures a even, balanced light across the entire room including the corners. This bracket comes in two pieces to be assembled on site to support a 5" cornice trim. We suggest that you allow about 3" from the top of the cornice to the ceiling, but results do vary depending on LED light intensity. Before determining positioning of this bracket and the cornice, we suggest you temporally mount a small section at various heights until you find the desired results.

    • US$14.00

    Score: 5.00 (votes: 1)
  • Drag and drop me to the cart

    MDF Bracket for LED Strip Lighting in 8ft sections. A great looking ceiling project is dependent on keeping a consistent distance from the strip light to the ceiling. This ensures a even, balanced light across the entire room including the corners. This bracket comes in two pieces to be assembled on site to support a 5" cornice trim. We suggest that you allow about 3" from the top of the cornice to the ceiling, but results do vary depending on LED light intensity. Before determining positioning of this bracket and the cornice, we suggest you temporally mount a small section at various heights until you find the desired results.

    • US$14.00

    Score: 5.00 (votes: 1)
  • Drag and drop me to the cart

    12V AC-DC power supply, 2 Amp. Can feed one roll of Bright LED (SMD3528) Strip. Dimensions: 3.75" X 1.75" X 1" (thickness) This product is UL (C, US) approved.

    • US$15.00

    Score: 5.00 (votes: 1)
  • Drag and drop me to the cart

    12V DC controller that uses Infrared Signal and pre-programmed. The remote control has a 6' range. Dimensions of the Controller: 4" X 2.5" X 1" (Thickness)

    • US$22.00

    Score: 5.00 (votes: 1)
  • Drag and drop me to the cart

    12V AC-DC power supply, 4 Amp. Can feed two rolls of Bright LED (SMD3528) Strips, or one roll of RGB, or one roll of Super Bright (SMD5050 with 30 LED's per meter) Strip. Dimensions: 4.5" X 2" X 1.25" This product is UL (C, US) approved.

    • US$25.00

    Score: 5.00 (votes: 1)
  • Drag and drop me to the cart

    12V DC RGB Amplifier is used to transfer RGB signals from one roll of RGB to another. Therefore, only one RGB controller is needed for the whole line. At the end of each roll, the Amplifier transfers the signals from that roll to the next. Each Amplifier needs to be connected to a 4A Power Supply. Dimensions of the Amplifier are 4" X 2.5" X 1" (Thickness).

    • US$25.00

    Score: 5.00 (votes: 1)
  • Drag and drop me to the cart

    12V AC-DC power supply, 6 Amp. Can feed one roll of Ultra Bright (SMD5050 with 60 LED's per meter) Strip. Dimensions: 5" X 2" X 1.25" This product is UL (C, US) approved.

    • US$32.00

    Score: 5.00 (votes: 1)
  • Drag and drop me to the cart

    12V DC controller that uses Radio Frequency Signal and pre-programmed. The remote control has a long range. Dimensions of the Controller are 4" X 2.5" X 1" (Thickness). The LED RF Controller is specially designed for controlling LED multicolor changing patterns. This controller offers a simple and fast installation. Great for controlling 12V RGB LED products.

    • US$32.00

    Score: 5.00 (votes: 1)